src/adafruit_blinka/microcontroller/ft232h/spi.py

   1 """SPI Class for FT232H"""
   2 from adafruit_blinka.microcontroller.ft232h.pin import Pin
   3
   4 # pylint: disable=protected-access
   5 class SPI:
   6     """Custom SPI Class for FT232H"""
   7
   8     MSB = 0
   9
  10     def __init__(self):
  11         # pylint: disable=import-outside-toplevel
  12         from pyftdi.spi import SpiController
  13
  14         # pylint: enable=import-outside-toplevel
  15
  16         self._spi = SpiController(cs_count=1)
  17         self._spi.configure("ftdi://ftdi:ft232h/1")
  18         self._port = self._spi.get_port(0)
  19         self._port.set_frequency(100000)
  20         self._port._cpol = 0
  21         self._port._cpha = 0
  22         # Change GPIO controller to SPI
  23         Pin.ft232h_gpio = self._spi.get_gpio()
  24
  25     # pylint: disable=too-many-arguments
  26     def init(
  27         self,
  28         baudrate=100000,
  29         polarity=0,
  30         phase=0,
  31         bits=8,
  32         firstbit=MSB,
  33         sck=None,
  34         mosi=None,
  35         miso=None,
  36     ):
  37         """Initialize the Port"""
  38         self._port.set_frequency(baudrate)
  39         # FTDI device can only support mode 0 and mode 2
  40         # due to the limitation of MPSSE engine.
  41         # This means CPHA must = 0
  42         self._port._cpol = polarity
  43         if phase != 0:
  44             raise ValueError("Only SPI phase 0 is supported by FT232H.")
  45         self._port._cpha = phase
  46
  47     # pylint: enable=too-many-arguments
  48
  49     @property
  50     def frequency(self):
  51         """Return the current frequency"""
  52         return self._port.frequency
  53
  54     def write(self, buf, start=0, end=None):
  55         """Write data from the buffer to SPI"""
  56         end = end if end else len(buf)
  57         chunks, rest = divmod(end - start, self._spi.PAYLOAD_MAX_LENGTH)
  58         for i in range(chunks):
  59             chunk_start = start + i * self._spi.PAYLOAD_MAX_LENGTH
  60             chunk_end = chunk_start + self._spi.PAYLOAD_MAX_LENGTH
  61             self._port.write(buf[chunk_start:chunk_end])
  62         if rest:
  63             self._port.write(buf[-1 * rest :])
  64
  65     # pylint: disable=unused-argument
  66     def readinto(self, buf, start=0, end=None, write_value=0):
  67         """Read data from SPI and into the buffer"""
  68         end = end if end else len(buf)
  69         result = self._port.read(end - start)
  70         for i, b in enumerate(result):
  71             buf[start + i] = b
  72
  73     # pylint: enable=unused-argument
  74
  75     # pylint: disable=too-many-arguments
  76     def write_readinto(
  77         self, buffer_out, buffer_in, out_start=0, out_end=None, in_start=0, in_end=None
  78     ):
  79         """Perform a half-duplex write from buffer_out and then
  80         read data into buffer_in
  81         """
  82         out_end = out_end if out_end else len(buffer_out)
  83         in_end = in_end if in_end else len(buffer_in)
  84         result = self._port.exchange(
  85             buffer_out[out_start:out_end], in_end - in_start, duplex=True
  86         )
  87         for i, b in enumerate(result):
  88             buffer_in[in_start + i] = b
  89
  90     # pylint: enable=too-many-arguments