Add additional SPI ports for BCM2711

[hackapet/Adafruit_Blinka.git] / src / adafruit_blinka / microcontroller / bcm283x / pin.py

diff --git a/src/adafruit_blinka/microcontroller/bcm283x/pin.py b/src/adafruit_blinka/microcontroller/bcm283x/pin.py
index 5b6ea24a925416abd181b0601348e3202dd3e28b..adbe183b7a32942cbd335763ca739d9b2f0cfd34 100644 (file)
--- a/src/adafruit_blinka/microcontroller/bcm283x/pin.py
+++ b/src/adafruit_blinka/microcontroller/bcm283x/pin.py
@@ -1,9 +1,13 @@
+"""Broadcom BCM283x pin names"""

 import RPi.GPIO as GPIO
 import RPi.GPIO as GPIO

-GPIO.setmode(GPIO.BCM)    # Use BCM pins D4 = GPIO #4
-GPIO.setwarnings(False)   # shh!

 
 

-# Pins dont exist in CPython so...lets make our own!
+GPIO.setmode(GPIO.BCM)  # Use BCM pins D4 = GPIO #4
+GPIO.setwarnings(False)  # shh!
+
+

 class Pin:
 class Pin:

+    """Pins dont exist in CPython so...lets make our own!"""
+

     IN = 0
     OUT = 1
     LOW = 0
     IN = 0
     OUT = 1
     LOW = 0


@@ -11,11 +15,11 @@ class Pin:
     PULL_NONE = 0
     PULL_UP = 1
     PULL_DOWN = 2
     PULL_NONE = 0
     PULL_UP = 1
     PULL_DOWN = 2

-    
+

     id = None
     _value = LOW
     _mode = IN
     id = None
     _value = LOW
     _mode = IN

-    
+

     def __init__(self, bcm_number):
         self.id = bcm_number
 
     def __init__(self, bcm_number):
         self.id = bcm_number
 


@@ -26,7 +30,8 @@ class Pin:
         return self.id == other
 
     def init(self, mode=IN, pull=None):
         return self.id == other
 
     def init(self, mode=IN, pull=None):

-        if mode != None:
+        """Initialize the Pin"""
+        if mode is not None:

             if mode == self.IN:
                 self._mode = self.IN
                 GPIO.setup(self.id, GPIO.IN)
             if mode == self.IN:
                 self._mode = self.IN
                 GPIO.setup(self.id, GPIO.IN)


@@ -35,7 +40,7 @@ class Pin:
                 GPIO.setup(self.id, GPIO.OUT)
             else:
                 raise RuntimeError("Invalid mode for pin: %s" % self.id)
                 GPIO.setup(self.id, GPIO.OUT)
             else:
                 raise RuntimeError("Invalid mode for pin: %s" % self.id)

-        if pull != None:
+        if pull is not None:

             if self._mode != self.IN:
                 raise RuntimeError("Cannot set pull resistor on output")
             if pull == self.PULL_UP:
             if self._mode != self.IN:
                 raise RuntimeError("Cannot set pull resistor on output")
             if pull == self.PULL_UP:


@@ -43,10 +48,11 @@ class Pin:
             elif pull == self.PULL_DOWN:
                 GPIO.setup(self.id, GPIO.IN, pull_up_down=GPIO.PUD_DOWN)
             else:
             elif pull == self.PULL_DOWN:
                 GPIO.setup(self.id, GPIO.IN, pull_up_down=GPIO.PUD_DOWN)
             else:

-                raise RuntimeError("Invalid pull for pin: %s" % self.id)       
+                raise RuntimeError("Invalid pull for pin: %s" % self.id)

 
     def value(self, val=None):
 
     def value(self, val=None):

-        if val != None:
+        """Set or return the Pin Value"""
+        if val is not None:

             if val == self.LOW:
                 self._value = val
                 GPIO.output(self.id, val)
             if val == self.LOW:
                 self._value = val
                 GPIO.output(self.id, val)


@@ -55,8 +61,13 @@ class Pin:
                 GPIO.output(self.id, val)
             else:
                 raise RuntimeError("Invalid value for pin")
                 GPIO.output(self.id, val)
             else:
                 raise RuntimeError("Invalid value for pin")

-        else:
-            return GPIO.input(self.id)
+            return None
+        return GPIO.input(self.id)
+
+
+# Pi 1B rev1 only?
+D0 = Pin(0)
+D1 = Pin(1)

 
 D2 = Pin(2)
 SDA = Pin(2)
 
 D2 = Pin(2)
 SDA = Pin(2)


@@ -76,7 +87,7 @@ MISO = Pin(9)
 D10 = Pin(10)
 MOSI = Pin(10)
 D11 = Pin(11)
 D10 = Pin(10)
 MOSI = Pin(10)
 D11 = Pin(11)

-SCLK = Pin(11) # Raspberry Pi naming
+SCLK = Pin(11)  # Raspberry Pi naming

 SCK = Pin(11)  # CircuitPython naming
 
 D12 = Pin(12)
 SCK = Pin(11)  # CircuitPython naming
 
 D12 = Pin(12)


@@ -103,16 +114,48 @@ D24 = Pin(24)
 D25 = Pin(25)
 D26 = Pin(26)
 D27 = Pin(27)
 D25 = Pin(25)
 D26 = Pin(26)
 D27 = Pin(27)

+D28 = Pin(28)
+D29 = Pin(29)
+D30 = Pin(30)
+D31 = Pin(31)
+D32 = Pin(32)
+D33 = Pin(33)
+D34 = Pin(34)
+D35 = Pin(35)
+D36 = Pin(36)
+D37 = Pin(37)
+D38 = Pin(38)
+D39 = Pin(39)
+D40 = Pin(40)
+MISO_2 = Pin(40)
+D41 = Pin(41)
+MOSI_2 = Pin(41)
+D42 = Pin(42)
+SCLK_2 = Pin(42)
+SCK_2 = Pin(43)
+D43 = Pin(43)
+D44 = Pin(44)
+D45 = Pin(45)

 
 # ordered as spiId, sckId, mosiId, misoId
 
 # ordered as spiId, sckId, mosiId, misoId

-spiPorts = ((0, SCLK, MOSI, MISO), (1, SCLK_1, MOSI_1, MISO_1))
+spiPorts = (
+    (0, SCLK, MOSI, MISO),
+    (1, SCLK_1, MOSI_1, MISO_1),
+    (2, SCLK_2, MOSI_2, MISO_2),
+    (3, D3, D2, D1), #SPI3 on Pi4/CM4
+    (4, D7, D6, D5), #SPI4 on Pi4/CM4
+    (5, D15, D14, D13), #SPI5 on Pi4/CM4
+    
+)

 
 # ordered as uartId, txId, rxId
 
 # ordered as uartId, txId, rxId

-uartPorts = (
-    (1, TXD, RXD),
-)
+uartPorts = ((1, TXD, RXD),)

 
 

+# These are the known hardware I2C ports / pins.
+# For software I2C ports created with the i2c-gpio overlay, see:
+#     https://github.com/adafruit/Adafruit_Python_Extended_Bus

 i2cPorts = (
     (1, SCL, SDA),
 i2cPorts = (
     (1, SCL, SDA),

+    (0, D1, D0),  # both pi 1 and pi 2 i2c ports!
+    (10, D45, D44),  # internal i2c bus for the CM4

 )
 )

-